Coaxial Cable Won’t Screw Into TV

You’re trying to get your coaxial cable screwed into the TV, but it won’t screw in? Not sure if you’re using the right coaxial cables, or if your tv just is too old and needs to be replaced? You got a lot of options. Here’s what to do.

Why is Coaxial Cable Won’t Screw Into TV?

If you’re having trouble screwing your coaxial cable into the input on your TV, it could be for a few reasons. First, make sure that the connector isn’t damaged. If there’s any damage to the threads or if they’re stripped in any way, this can cause problems when attaching the cable.

You may also have a bad connector on the RF input of your DVR or cable (check the threads). It’s possible that it’s not a problem with the cable itself—it could be that the connection on your TV is broken and/or that there’s a hard copper wire protruding from one side of it that prevents it from fitting properly.

How do you Screw in Coaxial Cable?

Screwing in coaxial cable is a simple process. You’ll need the right tools and supplies to get the job done right, though!

First, you’ll want to measure out how long you need your new cable to be. You can do this by measuring from one end of your current cable to the other, or by measuring from where you plan on cutting your new piece of cable to where it will connect with your device. Once you know how long you want it, cut off any extra length with wire cutters or scissors.

Next, take your screwdriver and press it into the center hole of the connector’s cap until it reaches the internal threads inside. This will loosen them up so that they’ll be easier to turn when attaching them to another piece of equipment later on down the road!

Now place one end of your new coaxial cable over top of one end of an existing piece of cable. Slide on over until they meet up with each other at their respective ends (like so).

Then take your screwdriver again—this time without pressing down—and hold it against both ends of each piece of cable at once so that they can be tightened together quickly and easily without worry about cracking either one.

What Happens if TV Coaxial Connector is Loose?

If your TV’s coaxial connector is loose, it can cause a few different problems. First, if the connection is too loose, you may lose all of your channels. If the connection is too tight, however, there’s a chance that you could damage your cable or the connector on the TV.

If you notice that your TV isn’t getting any channels or has poor reception, check to make sure that the coaxial connector isn’t loose. If it feels loose but still works well enough for you to watch TV without any major problems, consider tightening the connection with a pair of pliers and then re-checking your TV’s channels.

How do I Connect my Coax Cable to my TV?

To connect your coax cable to your TV, follow these simple steps:

  1. Connect one end of the cable to a wall outlet or power strip.
  2. Connect the other end of the cable to your TV.
  3. Plug in your TV and turn it on!

How do you Tighten a Coaxial Cable?

To tighten a coaxial cable, you’ll need a screwdriver and a ratchet. First, loosen the screws on the connector. Then, tighten the screws to secure the cable.

Recommended video for you…

Are all TV Coaxial Cables the Same?

One of the most common questions we hear is: “Are all TV coaxial cables the same?”

The answer is no. All TV coaxial cables are not created equal, and it’s important that you understand what makes them different and how to choose which one between them is right for you.

Conclusion

There are lots of ways to connect your TV to cable. You can use an RF connector and a coaxial jack, or an optical digital converter if your home theater system doesn’t have one built in. The digital converter converts the signal from an RF connection into a digital signal that can be read by TVs, home theater receivers and other devices with a digital connection such as HDMI.

If you have a questions and suggestions, please leave in the comment section below.

Click to rate this post!
[Total: 1 Average: 5]

Leave a Comment